Application37 matching SKUs12 standards covered
Construction & Infrastructure
Egyptian cement, clinker, aggregates and concrete additives shipped to construction projects worldwide — residential, commercial, infrastructure, marine and megaprojects. EN 197-1 / ASTM C150 grades, Mill Test Certificate per lot before B/L.
37
SKUs serving this industry
12
Standards & certs covered
7
Loading ports
60+
Destination markets
Construction & infrastructure
Egypt Globe Group ships cement (CEM I 42.5N / 52.5N, CEM II, SRC, White), clinker, aggregates, gypsum, limestone and concrete additives from 7 Egyptian seaports to construction markets in 60+ countries, alongside BS 4449 rebar, structural sections and dimension stone from its Metals and Construction divisions. Egypt holds roughly 85 million MT/year of installed cement capacity with a structural export surplus, and the group's role is to make that surplus procurable lot by lot: the right grade, the right standard, a Mill Test Certificate per lot before the Bill of Lading.
Contractors and ready-mix buyers do not fail on price; they fail on a silo of cement that sets early or a rebar heat below yield. Many regional exporters certify on the producer's typical values rather than the lot. EGG's Quality Assurance division — at the nucleus of the group since 2014 — samples at mill and silo, re-tests at the port laboratory and rejects at the loading port any lot outside the MTC, never re-graded or renegotiated.
Sub-applications served
Residential & commercial
ready-mix cement, blocks, plaster
Infrastructure megaprojects
bridges, dams, transmission towers, marine works
Precast & pre-stressed
high-strength factory concrete
Oilwell cementing
primary cementing, squeeze cementing, plug & abandonment, well completion
Sustainable construction
low-carbon CEM II, low-heat applications, GRC
Heavy industrial
heavy concrete shielding, refractory linings
Industry requirements
| Requirement | Typical tender specification | How EGG verifies it | Evidence issued |
|---|---|---|---|
| Cement strength class | CEM I 42.5N: 2-day ≥ 10 MPa, 28-day 42.5–62.5 MPa; CEM I 52.5N: 2-day ≥ 20 MPa, 28-day ≥ 52.5 MPa; CEM IV/B 32.5N: 28-day 32.5–52.5 MPa | EN 196-1 mortar prisms at port lab per lot | Mill Test Certificate before B/L |
| Chemical limits | SO₃ ≤ 3.5 % (CEM I 42.5N / CEM II) · ≤ 4.0 % (CEM I 52.5N) · ≤ 2.3 % (SRC); MgO ≤ 5.0 %; LOI ≤ 5.0 % (≤ 3.0 % SRC); chloride ≤ 0.10 %; C₃A ≤ 3.5 % SRC | XRF / wet chemistry per lot | MTC |
| Fineness and setting | Blaine ≥ 3,000 cm²/g (42.5N, SRC), ≥ 3,500 (CEM II, CEM IV, white), ≥ 4,000 (52.5N); initial set ≥ 75 min (42.5N), ≥ 45 min (52.5N) | Blaine + Vicat per lot | MTC |
| Clinker | C₃S ≥ 65 %, Blaine ≥ 310 m²/kg | XRD / Bogue per lot | Assay report |
| Aggregates | Crushed granite 20 mm, dolomite 10 mm chips; EN 12620 / EN 13043 / BS 812 gradation and ACV | Gradation and ACV per lot | Gradation report |
| Gypsum (retarder) | CaSO₄·2H₂O ≥ 85 % raw rock; plaster ≥ 90 % hemihydrate | XRF / wet chemistry per lot | CoA |
| Limestone (flux / filler) | CaCO₃ ≥ 95 %; dolomite CaMg 95 % | XRF per lot | CoA |
| Rebar | BS 4449 B500B: yield ≥ 500 N/mm², tensile ≥ 540 N/mm², elongation ≥ 14 % | Tensile test per heat | MTC per heat |
| Structural steel | S235JR / S275JR: yield 235–275 N/mm², tensile 360–510 N/mm² | Tensile test per heat | MTC per heat |
| Conformity | CE marking + Declaration of Performance (EU), SASO / SABER (GCC), BIS IS 269 (India), KEBS PVoC, SONCAP | Certificates per SKU; PSI through the partners | DoP, conformity certificate |
Matched supply
| Product | Grade / spec headline | Division | Standard | MOQ |
|---|---|---|---|---|
| CEM I 42.5N — ordinary Portland cement | 28-day 42.5–62.5 MPa, SO₃ ≤ 3.5 %, Blaine ≥ 3,000 | Construction | EN 197-1 / ASTM C150 Type I / ES 4756-1 | 5,000 MT |
| CEM I 52.5N — high-strength OPC | 2-day ≥ 20 MPa, 28-day ≥ 52.5 MPa, Blaine ≥ 4,000 | Construction | EN 197-1 / ASTM C150 Type III | 3,000 MT |
| CEM II / B-M (S-LL) 42.5N — composite | Slag 21–35 %, limestone 6–20 %, lower-CO₂ | Construction | EN 197-1 | 3,000 MT |
| SRC — sulphate resistant cement | C₃A ≤ 3.5 %, SO₃ ≤ 2.3 %, 28-day ≥ 35 MPa | Construction | ASTM C150 Type V / EN 197-1 SR3 | 3,000 MT |
| CEM IV / B (P) 32.5N — pozzolanic | Pozzolana 36–55 %, low heat, high sulphate resistance | Construction | EN 197-1 | 3,000 MT |
| White Portland cement | Fe₂O₃ ≤ 0.5 %, whiteness ≥ 85 % | Construction | EN 197-1 CEM I 42.5N white | 250 MT |
| Portland cement CEM I 52.5N · Portland clinker 65 % C₃S | Clinker Blaine ≥ 310 m²/kg | Construction | EN 197-1 / ASTM C150 | 1,000 MT |
| Oilwell cement Class G | API Spec 10A HSR | Construction | API 10A | 1,000 MT |
| Crushed granite aggregate 20 mm · dolomite 10 mm chips | Concrete / road base; asphalt | Construction | EN 12407, CE | 1,000 MT |
| Raw gypsum rock · plaster of Paris | CaSO₄·2H₂O ≥ 85 %; hemihydrate ≥ 90 % | Construction | ISO 9001, SGS | 1,000 MT |
| Limestone CaCO₃ 95 % bulk | Cement / steel flux | Construction | ISO 9001, SGS | 1,000 MT |
| Rebar BS 4449 B500B — Egyptian mill | 8–40 mm, yield ≥ 500 N/mm² | Metals | BS 4449 / EN 10080 | 500 MT |
| Steel sections — I / H / angle · galvanised sheet DX51D | S235JR / S275JR; Z100–Z275 | Metals | EN 10025-2 / EN 10346 | 250 MT |
| Porcelain floor tiles 60 × 60 cm · float glass 4 mm | ISO 13006 BIa; EN 572 | Construction | CE | 100 MT |
| Cement & clinker catalogue · construction division | — | Construction | EN 197-1 / ASTM C150 | 250–5,000 MT |
Loading ports: Damietta (EGDAM), Alexandria (EGALY), El Dekheila (EGEDK), Ain Sokhna (EGSOK); rebar and sections from Alexandria, El Dekheila, Damietta. Bulk vessel 2,000–65,000 MT, 1.5 MT sling bags, 50 kg PP bags palletised (20' FCL 25–27 MT); FOB / CFR / CIF. HS 2523.10 / 2523.29 / 2523.21 / 2517 / 2518 / 2520 / 2521 / 7214.
QA verification chain
| Gate | Control | Evidence | Who · frequency |
|---|---|---|---|
| Mill / quarry | Producer mill sampling — chemistry, Blaine, strength; quarry assay for gypsum, limestone, aggregates; heat analysis for steel | Producer MTC / quarry report | EGG QA · every production lot |
| Silo / yard | Silo sampling before discharge; stockpile sampling; strength-development tracking | Silo release record | EGG QA · per silo discharge |
| Port laboratory | EN 197-1 / ASTM C150 panel (chemistry, Blaine, setting, 2 / 7 / 28-day strength); gradation / ACV; XRF; tensile per heat | Mill Test Certificate or CoA before B/L; off-spec lot rejected | EGG port-side QC · every lot |
| Independent inspection | Sampling per EN 196-7 / ASTM C183, draft survey, hold and bag inspection, witness strength test | PSI certificate, draft survey | TÜV Austria (EU / GCC), SGS, Intertek, Bureau Veritas · per shipment on request |
| Destination acceptance | Buyer laboratory 28-day strength and chemistry check against MTC; spec guaranteed at port of loading under the sales contract; laycan discipline with NOR / SOF | Buyer acceptance, SOF | Buyer · per shipment |
Destination markets & compliance
- West Africa (Ghana, Nigeria, Côte d'Ivoire, Senegal) — SONCAP (Nigeria), Ghana conformity; Ghana · Nigeria
- East Africa (Kenya, Tanzania, Uganda, Mozambique) — KEBS PVoC, COMESA / AfCFTA origin; see the 50,000 MT cement under L/C and 12,000 MT OPC programme case studies
- GCC (KSA, UAE, Kuwait) — SASO / SABER, PAFTA; Saudi Arabia
- EU / Mediterranean — CE marking + DoP, EUR.1; South Asia — BIS IS 269 / 8112, India · Bangladesh
- Related: stone & architecture · steel & metalworking · cement & clinker market brief · HS 2523 reference · gypsum market · 2026 cement buyer's guide
Standards & documentation
- EN 197-1 · ASTM C150 · BS 12 · GOST 31108 · API 10A (oilwell) · BS 4449 / EN 10080 (rebar) · EN 12620 / EN 13043 (aggregates)
- Mill Test Certificate per shipment; independent TÜV Austria / SGS / Intertek / Bureau Veritas inspection — trade documentation · inspection · quality & compliance · vessel sizes
Request a quote
State the grade, standard, packing, tonnage and discharge port; the trade desk returns a matched SKU, MTC template and FOB / CFR / CIF price within 24 hours. Request a quote
Matching SKUs
37 products for construction & infrastructure
Sourced from 3 of our 7 product divisions.
From Construction (31)
HS 2523.29.00
CEM I 42.5N — Ordinary Portland Cement
EN 197-1:2011 · ASTM C150 Type I · ISO 9001:2015
HS 2523.29.00
CEM I 52.5N — High-Strength OPC
EN 197-1:2011 · ASTM C150 Type III · ISO 9001:2015
HS 2523.29.00
CEM II / B-M (S-LL) 42.5N — Composite
EN 197-1:2011 · ISO 9001:2015 · Egyptian ES
HS 2515.11.00
Galala Cream Marble — Egyptian Premium
ISO 9001:2015 · EN 12058 (paving) · EN 1469 (cladding)
HS 2523.29.00
SRC — Sulphate Resistant Cement
ASTM C150 Type V · EN 197-1 SR3 · ISO 9001:2015
HS 2515.11.00
Sinai Pearl Marble — Beige Premium
ISO 9001:2015 · EN 12058 · EN 1469
HS 2523.21.00
White Portland Cement — Decorative + Architectural
EN 197-1:2011 · ASTM C150 · ISO 9001:2015
HS 2523.29.00
CEM IV / B (P) 32.5N — Pozzolanic Cement
EN 197-1:2011 · ISO 9001:2015 · Egyptian ES
HS 2516.11.00
Rosa Aswan Granite — Pink Egyptian
ISO 9001:2015 · EN 12058 · EN 1469
HS 2523.29.00
Oilwell Cement Class G — API Spec 10A
API Spec 10A Class G HSR · ISO 9001:2015 · MTC per shipment
HS 2515.11.00
Sunny Yellow Marble — Egyptian Classic
ISO 9001:2015 · EN 12058 · EN 1469
HS 2516.11
Aswan Red Granite Blocks
CE Mark · EN 12407 · SGS
HS 2520.20
Calcined Gypsum Plaster of Paris
ISO 9001:2015 · SGS
HS 2836.50
Calcium Carbonate Powder Coated
ISO 9001:2015 · SGS
HS 2517.10
Crushed Granite Aggregate 20mm
CE Mark · EN 12407 · SGS
HS 4401.22
Eucalyptus Wood Chips Pulp Grade
ISO 9001:2015 · SGS
HS 7005.29
Float Glass Clear 4mm
ISO 9001:2015 · SGS
HS 4805.11
Kraft Liner 125gsm Natural
ISO 9001:2015 · SGS
HS 6908.90
Porcelain Floor Tiles 60x60cm Polished
ISO 9001:2015 · SGS
HS 2523.29
Portland Cement CEM I 52.5N
EN 197-1 · ASTM C150 · ISO 9001:2015
HS 6802.21
Crema Sahara Limestone Tiles
CE Mark · EN 12407 · SGS
HS 2518.10
Dolomite
ISO 9001:2015 · SGS
HS 2518.10
Dolomite Aggregate 10mm Chips
CE Mark · EN 12407 · SGS
HS 4707.10
OCC 11 Old Corrugated Containers
ISO 9001:2015 · SGS
HS 4407.11
Pine Sawn Timber C24 KD
ISO 9001:2015 · SGS
HS 2523.10
Portland Clinker 65% C3S
EN 197-1 · ASTM C150 · ISO 9001:2015
HS 2520.10
Raw Gypsum Rock
ISO 9001:2015 · SGS
HS 2516.11
Granite Blocks
CE Mark · EN 12407 · SGS
HS 2521.00
Limestone CaCO3 95% Bulk
ISO 9001:2015 · SGS
HS 6802.21
Marble Tiles
CE Mark · EN 12407 · SGS
HS 6802.21
Sinai Pearl Marble Slabs 2cm
CE Mark · EN 12407 · SGS
From Industrial Minerals (1)
From Metals & Alloys (5)
HS 7214.20.00
Rebar BS 4449 Grade B500B — Egyptian Mill
BS 4449:2005+A3:2016 Grade B500B · EN 10080 · ISO 9001:2015
HS 7208.10.00
HRC — Hot-Rolled Coil S235JR
EN 10025-2 S235JR · ASTM A36 · ISO 9001:2015
HS 7210.49.00
Galvanised Steel Sheet — DX51D Z275
EN 10346 DX51D · ASTM A653 CS Type B · ISO 9001:2015
HS 7213.91.00
Steel Wire Rod SAE 1006-1018
EN 10016 / ASTM A510 · SAE 1006-1018 · ISO 9001:2015
HS 7216.40.00
Steel Sections — I-Beam / H-Beam / Angle
EN 10025-2 S235JR / S275JR · ASTM A36 / A992 · ISO 9001:2015
Standards & Certifications Covered
SKUs in this application carry paperwork ready for the standards below.
✓ ISO 9001:2015✓ SGS verified✓ EN 197-1:2011✓ ASTM C150 Type I✓ Egyptian ES 4756-1✓ Mill Test Certificate per shipment✓ ASTM C150 Type III✓ MTC per shipment✓ Egyptian ES✓ Lower-CO₂ alternative✓ BS 4449:2005+A3:2016 Grade B500B✓ EN 10080
Other applications served
Have a construction & infrastructure requirement?
Tell us your tender spec — we'll come back within 24 hours with priced FOB / CIF / CFR options matched to your industry's standards.
Request a Quote